Tag Archives: Actuator

CONTROL VALVE: OPERATION, MAINTENANCE AND TROUBLESHOOTING – Half Confirmed

ACARA

21 – 23 November 2017 | Rp 6.000.000 di Yogyakarta – HALF CONFIRMED
05 – 07 Desember 2017 | Rp 6.000.000 di Yogyakarta – HALF CONFIRMED
20 – 22 Desember 2017 | Rp 6.000.000 di Yogyakarta

 

 

DESKRIPSI TRAINING CONTROL VALVE

Elemen kontrol yang paling utama dalam proses kontrol industri adalah control valve. Control valve memanipulasi cairan mengalir, seperti gas, uap, air, atau senyawa kimia, untuk mengimbangi gangguan beban dan menjaga proses regulasi variabel diatur sedekat mungkin dengan set point yang diinginkan. Control valve assembly biasanya terdiri dari badan katup, bagian internal, aktuator untuk memberikan motive power untuk mengoperasikan valve, dan berbagai aksesoris valve tambahan, yang dapat mencakup positioner, transduser, supply pressure regulators, operator manual, snubbers, atau limit switch. Control valve atau perakitan control valve tidak sepenting mengakui bahwa control valve adalah bagian penting dari control loop. Hal ini tidak akurat untuk mengatakan bahwa control valve adalah bagian paling penting dari loop. Control loop adalah sebagai rantai instrumentasi. Seperti rantai lainnya, seluruh rantai hanya sebagai baik sebagai link terlemah. Hal ini penting untuk memastikan bahwa katup kontrol tidak link terlemah. Dalam pelatihan ini akan dibahas mengenai definisi untuk kontrol proses, sliding-stem control valve, rotary-shaft control valve, dan fungsi control valve lainnya dan karakteristik terminologi.

TUJUAN TRAINING CONTROL VALVE

Tujuan pelatihan:

  • Dapat memahami konsep dasar dan cara kerja valve;
  • Dapat memahami mengenai control valve, actuator, and positioner designs dan aplikasinya;
  • Dapat mengoperasikan dan merawat valve dengan baik;
  • Dapat mengetahui metode untuk mengidentifikasi problem dan kegagalan valve secara spesifik dan solusi untuk mengatasi/memperbaikinya.

MATERI TRAINING CONTROL VALVE

  1. Introduction:
  • Teori Dasar Sistem Kerja Valve
  • Process Control Terminology
  • Sliding-Stem Control Valve Terminology
  • Rotary-Shaft Control Valve Terminology
  • Control Valve Functions & Characteristics Terminology
  • Control Valve Standards – Ansi & Api
  1. Control Valve Performance:
  • Dead Band
  • Actuator-Positioner Design
  • Valve Response Time
  • Valve Type & Characterization
  • Valve Sizing.
  1. Valve and Actuator Types:
  • Control Valves
  • Control Valve End Connections
  • Valve Body Bonnets
  • Control Valve Packing
  • Characterization of Cage-Guided Valve Bodies
  • Valve Plug Guiding, Restricted-Capacity Control Valve Trim
  • Actuators
  1. Valve Operation & Control:
    • Valve As Instrument Control
    • Valve Control  Star System: What Is Valve Yard And How Its Operated.
    • Valve Control  Noise
    • Valve Control Cavitations
  2. Control Valve Accessories:
  • Positioners
  • Other Control Valve Accessories
  1. Control Valve Selection:
  • Valve Body Material
  • Designations for the High Nickel alloys
  • Pressure-Temperature Ratings for Standard Class
  • Face-to-Face Dimensions
  • Control Valve Seat Leakage Classifications
  • Control Valve Flow Characteristics
  • Valve Sizing
  • Non-Destructive Test Procedures
  • Cavitation and Flashing
  1. Special Control Valves:
  • High Capacity Control Valves
  • Low Flow Control Valves
  • High-Temperature Control Valves
  • Cryogenic Service Valves
  • Customized Characteristics and Noise Abatement Trims
  • Valves Subject to Sulfide Stress Cracking
  1. Practice Assembly & Disassembly Valve;
    • Installation & Maintenance
    • Valve Disassembly – Assembly /Hands On
    • Valve Failure On Component & How Inspection
    • Valve Testing (Theory)
  2. Installation & Maintenance:
  • Proper Storage & Protection
  • Proper Installation Techniques
  • Control Valve Maintenance
  • Actuator Diaphragm
  • Stem Packing, Seat Rings, Bench Set
  1. Troubleshooting

PESERTA TRAINING CONTROL VALVE

Pelatihan ini sesuai untuk diikuti oleh para Instrumentation & Control Engineers & Technicians, Mechanical Engineers & Technicians, Projects Engineers, Operation Engineers, Process & Utility Supervisors, Technical Supervisory, Plant Maintenance/Oparetors/Supervisor/Superintendent, dan personel lain yang dalam pekerjaan terlibat dalam Sizing, Selecting, and Applying Process Control Valves.

METODE:

  • Presentasi
  • Diskusi Interaktif
  • Studi Kasus
  • Simulasi
  • Evaluasi

INSTRUKTUR:

  • Teguh Pudji Purwanto, MT.
  • Sigit Budi Hartono, ST., MT.

Nara sumber adalah pakar di bidang Mechanical Engineering yang sering memberikan materi di berbagai training, seminar, workshop, terutama yang berkaitan dengan topik Control Valve: Operation, Maintenance & Troubleshooting.

WAKTU & TEMPAT TRAINING CONTROL VALVE

  • Batch 10 : 21 – 23 November 2017 (almost running – Yogyakarta)
  • Batch 11 : 5 – 7 Desember 2017
  • Batch 12 : 20 – 22 Desember 2017
  • 08.00 – 16.00 WIB

Yogyakarta: Ibis Styles Hotel Yogyakarta ; Cavinton Hotel Yogyakarta ; Neo Malioboro Hotel Yogyakarta
Surabaya: Hotel Santika Pandegiling Surabaya
Malang: Best Western OJ Hotel Malang ; Harris Hotel & Convention Malang
Jakarta: Ibis Jakarta Arcadia Hotel ; Ibis Jakarta Tamarin Hotel
Bandung: Golden Flower Hotel Bandung
Bali: Ibis Bali Kuta Hotel ; Harris Kuta Raya Hotel Bali

In House Training : Depend on request

BIAYA TRAINING CONTROL VALVE

Yogyakarta:

  • Publish Rate              : Rp 6.000.000,- /participant
  • Special Rate              : Rp 5.500. 000,- /participant (min 3 participants from the same company)

Bandung / Jakarta / Surabaya / Malang:

  • Publish Rate              : Rp 7.000.000,- /participant

Bali:

  • Publish Rate              : Rp 8.000.000,- /participant

FASILITAS:

  • Meeting Room at Hotel
  • Coffe Break & Lunch
  • Module (hard & soft copy/flashdish)
  • Training Kit & Souvenir
  • Sertifikat
  • Airport pick up services
  • Transportation during training

CONTROL VALVE: OPERATION, MAINTENANCE AND TROUBLESHOOTING

Formulir Pra-Pendaftaran Public Training / Permintaan Informasi Lebih Lanjut
  1. JENIS INFORMASI/TRAINING
  2. (required)
  3. (required)
  4. DATA PRIBADI
  5. (required)
  6. (required)
  7. (required)
  8. (valid email required)
  9. (required)
  10. (required)
  11. DATA PRE REGISTRATION (Tidak Mengikat)
  12. (required)
  13. PESAN UNTUK PENYELENGGARA TRAINING
 

cforms contact form by delicious:days

Valve & Actuator: Operation and Maintenance

ACARA

06 – 08 November 2017 | Rp 6.900.000,- per peserta di Hotel Ibis, Yogyakarta
13 – 15 November 2017 | Rp 6.900.000,- per peserta di Hotel Ibis, Yogyakarta
20 – 22 November 2017 | Rp 6.900.000,- per peserta di Hotel Ibis, Yogyakarta
27 – 29 November 2017 | Rp 6.900.000,- per peserta di Hotel Ibis, Yogyakarta

Jadwal Training 2017 Selanjutnya …

02 – 04 Januari 2018 | Rp 6.900.000,- per peserta di Hotel Ibis, Yogyakarta
08 – 10 Januari 2018 | Rp 6.900.000,- per peserta di Hotel Ibis, Yogyakarta

Jadwal Training 2018 Selanjutnya …

 

 

DESKRIPSI Training Valve & Actuator

Valves are, unquestionably, the most important part of any piping and pumping system because they direct the flow of fluids and regulate temperatures. Properly used and maintained, they can improve process efficiency and lower costs. It is wise to apply the basics of proper valve maintenance in ways that improve their life cycle and operating efficiency. Here are eight often-overlooked valve maintenance basics that can help you do just that.

 

MATERI Training Valve & Actuator

  1. Maintenance :
  • Reactive Maintenance
  • Preventive Maintenance
  • Predicr\tive Maintenance
  • Proactive maintenance
  1. Construction, Maintenance and repair of
  • Valve :
  1. Control Valve
  2. Gate Valve
  3.  Safety Valve
  1. Actuator:
  • Hydraulic
  •  Pneumatic
  • Electromagnetic
  1. Valve Problems and Maintenance Activities:

Noise in valve, Noise Control, Fluid behaviors, Problems in control valve and its solution, Maintenance problems of control valve, Troubleshooting analysis, Hands-on activities

 

Metode Training Valve & Actuator

Presentasi, Diskusi , Studi Kasus

Jadwal Training 2017

Hotel Ibis Malioboro ,Yogjakarta

  • 16 – 18 Oktober 2017
  • 23 – 25 Oktober 2017
  • 30 Oktober – 01 November 2017
  • 06 – 08 November 2017
  • 13 – 15 November 2017
  • 20 – 22 November 2017
  • 27 – 29 November 2017
  • 04 – 06 Desember 2017
  • 11 – 13 Desember 2017
  • 18 – 20 Desember 2017
  • 27 – 29 desember 2017

 

Jadwal Training 2018

Hotel Ibis Malioboro ,Yogjakarta

  • 02 – 04 Januari 2018
  • 08 – 10 Januari 2018
  • 15 – 17 Januari 2018
  • 22 – 24 Januari 2018
  • 29 – 31 Januari 2018
  • 05 – 07 Februari 2018
  • 12 – 14 Februari 2018
  • 19 – 21 Februari 2018
  • 26 – 28 Februari 2018
  • 05 – 07 Maret 2018
  • 12 – 14 Maret 2018
  • 19 – 21 Maret 2018
  • 26 – 28 Maret 2018
  • 02 – 04 April 2018
  • 09 – 11 April 2018
  • 16 – 18 April 2018
  • 23 – 25 April 2018
  • 02 – 04 Mei 2018
  • 07 – 09 Mei 2018
  • 14 – 16 Mei 2018
  • 21 – 23 Mei 2018
  • 30 Mei – 01 Juni 2018
  • 04 – 06 Juni 2018
  • 25 – 27 Juni 2018
  • 02 – 04 Juli 2018
  • 09 – 11 Juli 2018
  • 16 – 18 Juli 2018
  • 23 – 25 Juli 2018
  • 30 Juli – 01 Agustus 2018
  • 06 – 08 Agustus 2018
  • 13 – 15 Agustus 2018
  • 20 – 21 Agustus 2018
  • 27 – 29 Agustus 2018
  • 03 – 05 September 2018
  • 12 – 14 September 2018
  • 17 – 19 September 2018
  • 24 – 26 September 2018
  • 01 – 03 Oktober 2018
  • 08 – 10 Oktober 2018
  • 15 – 17 Oktober 2018
  • 22 – 24 Oktober 2018
  • 29 – 31 Oktober 2018
  • 05 – 07 November 2018
  • 12 – 14 November 2018
  • 21 – 23 November 2018
  • 26 – 28 November 2018
  • 03 – 05 Desember 2018
  • 10 – 12 Desember 2018
  • 17 – 19 Desember 2018
  • 26 – 28 Desember 2018



Investasi dan Fasilitas Training

  • Rp.6.900.000 (Non Residential)
    • VIP training Rp 8.9000 (4 Hari , Non Residential dengan tambahan Fasilitas Paket studi lapangan/ City tour dan Belum Termasuk Pajak PPn 10%)
  • Quota minimum 2 peserta
  • Fasilitas : Certificate,Training kits, USB,Lunch,Coffe Break, Souvenir
  • Untuk peserta luar kota disediakan transportasi antar-jemput dari Bandara/Stasiun ke Hotel (berlaku bagi perusahaan yang mengirimkan minimal 3 peserta)

 

Instruktur Training Valve & Actuator

Ir. Paryana Puspaputra, M.Eng. and Team

 

Valve & Actuator: Operation and Maintenance

Formulir Pra-Pendaftaran Public Training / Permintaan Informasi Lebih Lanjut
  1. JENIS INFORMASI/TRAINING
  2. (required)
  3. (required)
  4. DATA PRIBADI
  5. (required)
  6. (required)
  7. (required)
  8. (valid email required)
  9. (required)
  10. (required)
  11. DATA PRE REGISTRATION (Tidak Mengikat)
  12. (required)
  13. PESAN UNTUK PENYELENGGARA TRAINING
 

cforms contact form by delicious:days

VALVES & ACTUATOR: OPERATION AND MAINTENANCE

EVENT

02 – 03 Mei 2017  | Rp. 6.900.000 Per Peserta di Yogyakarta /Semarang / Solo
02 – 03 Mei 2017 | Rp. 7.900.000 Per Peserta di Bandung / Jakarta / Surabaya
02 – 03 Mei 2017 | Rp. 8.900.000 Per Peserta di Bali / Batam /Balikpapan / Manado / Lombok
08 – 09 Mei 2017  | Rp. 6.900.000 Per Peserta di Yogyakarta /Semarang / Solo

Jadwal Training 2017 Selanjutnya …

 

 



DESKRIPSI TRAINING VALVES & ACTUATOR 

Valves are, unquestionably, the most important part of any piping and pumping system because they direct the flow of fluids and regulate temperatures. Properly used and maintained, they can improve process efficiency and lower costs. It is wise to apply the basics of proper valve maintenance in ways that improve their life cycle and operating efficiency. Here are eight often-overlooked valve maintenance basics that can help you do just that.



MATERI TRAINING VALVES & ACTUATOR

  • Maintenance :
    • Reactive Maintenance
    • Preventive Maintenance
    • Predicr\tive Maintenance
    • Proactive maintenance
  • Construction, Maintenance and repair of
    • Valves :
    • Control Valves
    • Gate Valves
    • Safety Valves
  • Actuator:
    • Hydraulic
    •  Pneumatic
    • Electromagnetic
  • Valves Problems and Maintenance Activities:

Noise in valves, Noise Control, Fluid behaviors, Problems in control valve and its solution, Maintenance problems of control valves, Troubleshooting analysis, Hands-on activities

 



METODE TRAINING VALVES & ACTUATOR

Presentasi, Diskusi , Studi Kasus

 

Jadwal Training 2017

Hotel Santika Kuta, Bali
Hotel Nagoya Plaza, Batam
Hotel Fave, Balikpapan
Hotel Aston, Manado
Hotel Lombok Raya, Mataram
Hotel Serela Merdeka, Bandung
Hotel Santika Pandegiling, Surabaya
Sofyan Hotel Betawi, Jakarta
Hotel Ibis Solo
Hotel Ibis Simpang Lima, Semarang
Hotel Ibis Malioboro, Yogyakarta

  • 25 – 26 April 2017
  • 02 – 03 Mei 2017
  • 08 – 09 Mei 2017
  • 15 – 16 Mei 2017
  • 22 – 23 Mei 2017
  • 29 – 30 Mei 2017
  • 05 – 06 Juni 2017
  • 12 – 13 Juni 2017
  • 19 – 20 Juni 2017
  • 03 – 04 Juli 2017
  • 10 – 11 Juli 2017
  • 17 – 18 Juli 2017
  • 24 – 25 Juli 2017
  • 31 Juli – 01 Agustus 2017
  • 07 – 08 Agustus 2017
  • 14 – 15 Agustus 2017
  • 21 – 22 Agustus 2017
  • 28 – 29 Agustus 2017
  • 04 – 05 September 2017
  • 11 – 12 September 2017
  • 18 – 19 September 2017
  • 25 – 26 September 2017
  • 02 – 03 Oktober 2017
  • 09 – 10 Oktober 2017
  • 16 – 17 Oktober 2017
  • 23 – 24 Oktober 2017
  • 30 – 31  Oktober 2017
  • 06 – 07 November 2017
  • 13 – 14 November 2017
  • 20 – 21 November 2017
  • 27 – 28 November 2017
  • 04 – 05 Desember 2017
  • 11 – 12 Desember 2017
  • 18 – 19 Desember 2017
  • 27 – 28 desember 2017

 

 

Investasi dan Fasilitas

  • Rp 8.900.000 (Non Residential) untuk lokasi di Bali, Batam, Balikpapan, Manado atau Lombok
  • Rp 7.900.000 (Non Residential) untuk lokasi di Bandung, Jakarta atau Surabaya
  • Rp 6.900.000 (Non Residential) untuk Lokasi Solo, Semarang atau Yogyakarta
  • Quota minimum 2 peserta
  • Quota minimum 3 peserta ( Untuk Manado, Balikpapan dan Lombok Quota minimal 4 peserta)
  • Fasilitas : Certificate,Training kits, USB,Lunch,Coffe Break, Souvenir
  • Untuk peserta luar kota disediakan transportasi antar-jemput dari Bandara/Stasiun ke Hotel khusus bagi perusahaan yang mengirimkan minimal 3 orang peserta)

 

 

Instruktur

Ir Teguh Pudji Poerwanto MT and Team



OPERATION AND MAINTENANCE OF VALVES & ACTUATOR

Formulir Pra-Pendaftaran Public Training / Permintaan Informasi Lebih Lanjut
  1. JENIS INFORMASI/TRAINING
  2. (required)
  3. (required)
  4. DATA PRIBADI
  5. (required)
  6. (required)
  7. (required)
  8. (valid email required)
  9. (required)
  10. (required)
  11. DATA PRE REGISTRATION (Tidak Mengikat)
  12. (required)
  13. PESAN UNTUK PENYELENGGARA TRAINING
 

cforms contact form by delicious:days

CONTROL VALVES AND CHOKE

EVENT

20 – 23 Februari 2017 | Rp 8.500.000/person di Bandung
20 – 23 Maret 2017 | Rp 8.500.000/person di Bandung
24 – 27 April 2017 | Rp 8.500.000/person di Bandung
29 Mei – 01 Juni 2017 | Rp 8.500.000/person di Bandung

Jadwal Training 2017 Selanjutnya …


 

TRAINING INTRODUCTION CONTROL VALVES AND CHOKE

This course is developed for engineers and technicians who need to have a practical knowledge of selection, installation  of choke and control valves. It is for those primarily involved in achieving effective results in industrial processes. This would involve the design, specification and implementation of control and measurement equipment. The workshop focuses on practical applications, with special attention to installation considerations and application limitations when selecting or installing different control valves.

 

TRAINING METHODOLOGY CONTROL VALVES AND CHOKE

The latest educational methods and strategies will be employed. The course is designed to maximise benefit from the outset. Questions are encouraged throughout, to provide participants with the opportunity to discuss with the presenter and others, specific problems and appropriate solutions. All delegates take away a detailed and comprehensive copy of the materials, and practical exercise using software will be provided to ensure knowledge retention.

 

TRAINING MATERIAL OUTLINE CONTROL VALVES AND CHOKE

  1. Basic physical properties
  2. Fundamental of measurement
  3. Fundamentals of flow characteristics
  4. Valve types
  5. Pressure valve
  6. Actuator
  7. Control valves
  8. Realistic Control valve
  9. Pressure drop
  10. Flow equations
  11. Fundamental valve sizing
  12. Sizing for liquid
  13. Sizing for gas
  14. Control valve selection
  15. Installation
  16. Standards
  17. Choke Valves


TRAINING INSTRUCTOR CONTROL VALVES AND CHOKE

Ir.Endra Joelianto, Ph.D

Ir.Endra Joelianto, Ph.D. is an expert in control engineering and industrial automation. His outstanding research is: Hybrid Control Systems, Discrete Event Control Systems, Petri Nets Analysis and Application on PLC, Robust and Advanced PID Controller and its implementation on PLC, DCS, Fieldbus, Industrial automation and Advanced Control System Designs. He received first degree (Ir.) in Engineering Physics in 1990 from Department of Engineering Physics, ITB and Doctor of Philosofy (PhD.) in Control Engineering in 2001 from Department of Engineering, The Australian National University, Canberra, Australia.  He is Head of Intelligent Control and Automation Laboratory and Coordinator of PLC Research Group for research and training, Engineering Physics Study Program and Instrumentation and Control Research Division, Institut Teknologi Bandung. He was Director of Schneider-OMRON PLC Training Center, Maranatha Christian University, Bandung.  He has attended several professional training on PLC, DCS and Instruments Callibration, such as: Yokogawa DCS, Bandung (2000), Implementation of Indonesian National Standard (SNI) 19-17025 and Basic Calibration, Yokogawa Electric Corporation, Bandung (2001), Fieldbus Foundation Technology, Singapore (2002), Basic and Advanced PLC Telemecanique-TWIDO, Bandung (2003), Basic and Advanced PLC OMRON, Jakarta (2004), Cleaner Production Application in Industries (Bandung 2005), Effective Energy Systems for Sustainable Development (Thailand 2006), Programming and Networking PLC Mitsubishi (2006), InTouch Wonderware, Wonderware Historian and Information Server (Bandung, 2012). He also has hosted Workshop on Industrial Automation (Bandung, 2002) and (Bandung, 2003), Workshop on Application of PLC in Industrial Automation (Bandung, 2003), National Workshop on Instrumentation & Control (2011) and many professional trainings on PLC, DCS, SCADA, Human Machine Interface and Industrial Process Control and Automation in Bandung. He was the project leader of Department of National Education TPSDP Retooling Program Batch II on Industrial Automation using PLC (2004). He is the chairman of National Student Competition on PLC Programming held regularly since 2007 in ITB. He serves as instructor either for public or for in-house training on instrumentation and process control to universities, industries, petrochemical or oil and gas companies, such as: PT. NGL Arun, PT. NGL Bontang, PT. Pupuk Iskandar Muda, PT. Pupuk Kalimantan Timur, PT. Pupuk Kujang, PT. Semen Padang, PT. Semen Gresik, PT. Semen Cibinong, PT. Indocement, PT. Semen Tigaroda Perkasa, PT. Exspan Nusantara, PERTAMINA, British Petroleoum, Maxus, Gulf, PT. Chevron Geothermal, PT. Chevron Pacific Indonesia,

TRAINING VENUE CONTROL VALVES AND CHOKE

Kagum Group Hotel Bandung (Golden Flower, Banana Inn, Serela, Gino Feruci), Amaroossa Hotel, Noor Hotel, Grand Setiabudi Hotel, dll


TRAINING DURATION

4 days

  JADWAL TRAINING

  1. 20 Feb 2017-23 Feb 2017
  2. 20 Mar 2017-23 Mar 2017
  3. 24 Apr 2017-27 Apr 2017
  4. 29 May 2017-01 Jun 2017
  5. 06 Jun 2017-09 Jun 2017
  6. 24 Jul 2017-27 Jul 2017
  7. 28 Aug 2017-31 Aug 2017
  8. 25 Sep 2017-28 Sep 2017
  9. 23 Oct 2017-26 Oct 2017
  10. 20 Nov 2017-23 Nov 2017
  11. 04 Dec 2017-07 Dec 2017

INVESTATION PRICE/PERSON :

  1. Rp 8.500.000/person (full fare)  or
  2. Rp 8.250.000/person (early bird, payment 1 week before training)  or
  3. Rp 7.950.000/person (if there are 3 or more participants from the same company)

 

FACILITIES FOR PARTICIPANTS :

  •     Training Module
  •     Flashdisk contain training material
  •     Certificate
  •     NoteBook and Ballpoint
  •     T-Shirt
  •     Backpack
  •     Training Foto
  •     Training room with full ac facilities and multimedia
  •     Lunch and twice coffee break everyday of training
  •     Qualified Instructor
  •     Transportation from hotel of participants to hotel of training VV (if minimal participants from the same company is 4 )

CONTROL AND CHOKE VALVES

Formulir Pra-Pendaftaran Public Training / Permintaan Informasi Lebih Lanjut
  1. JENIS INFORMASI/TRAINING
  2. (required)
  3. (required)
  4. DATA PRIBADI
  5. (required)
  6. (required)
  7. (required)
  8. (valid email required)
  9. (required)
  10. (required)
  11. DATA PRE REGISTRATION (Tidak Mengikat)
  12. (required)
  13. PESAN UNTUK PENYELENGGARA TRAINING
 

cforms contact form by delicious:days