MACHINERY FAILURE ANALYSIS AND TROUBLESHOOTING

ACARA

26 – 28 April 2017 | Rp 6.000.000,- di Hotel Fave Melawai, Jakarta
16 – 18 Mei 2017 | Rp 6.000.000,- di Hotel Fave Melawai, Jakarta
15 – 17 Juni 2017 | Rp 6.000.000,- di Hotel Fave Melawai, Jakarta
13 – 15 Juli 2017 | Rp 6.000.000,- di Hotel Fave Melawai, Jakarta

Jadwal Training 2017 Selanjutnya …

 

INTRODUCTION MACHINERY FAILURE ANALYSIS AND TROUBLESHOOTING

Reliability engineering and predictive maintenance have two major objectives: preventing catastrophic failure of critical plant production systems and avoiding deviations from acceptable performance levels that result in personal injury, environmental impact, capacity loss, or poor product quality. Unfortunately, these events will occur no matter how effective the reliability program. Therefore, a viable program must include a process for fully understanding and correcting the root causes that lead to events having an impact on plant performance. The course gives a logical approach to problem solution. The method can be used to accurately define deviations from acceptable performance levels, isolate the root causes of equipment failures, develop cost-effective corrective actions that prevent recurrence. This set is a practical, step-by-step guide for evaluating most recurring and serious incidents that may occur in a plant. The purpose of RCFA & FMEA is to resolve problems that affect plant performance. It should be an attempt to fix blame for the incident. The use of RCFA & FMEA should be carefully scrutinized before undertaking a full investigation because of the high cost associated with performing such an in depth analysis.

MATERIAL OUTLINE MACHINERY FAILURE ANALYSIS AND TROUBLESHOOTING

  1. The Failure Analysis and Troubleshooting System
  2. Metalurgical Failure Analysis
  3. Machinery Component Failure Analysis
  4. Machinery Troubleshooting
  5. Vibration Analysis
  6. Generalized Machinery Problem-Solving Sequence
  7. The “Seven-Cause Category Approach” to Root-Cause Failure Analysis
  8. Cause Analysis by Pursuing the Cause-and-Effect Relationship
  9. Knowledge-Based Systems for Machinery Failure Diagnosis

METODE MACHINERY FAILURE ANALYSIS AND TROUBLESHOOTING

Kegiatan pelatihan dirancang agar peserta dapat memahami secara komprehensif materi yang disampaikan, sehingga dapat dimplementasikan secara aplikatif dalam dunia kerja. Adapun metode yang digunakan adalah:

  1. Presentation
  2. Discuss
  3. Case Study
  4. Evaluation

Instructor MACHINERY FAILURE ANALYSIS AND TROUBLESHOOTING

Cecep Slamet Abadi, ST, MT

( Senior Praktisi Listrik dan Mesin yang sangat berpengalaman dan sudah bersertifikasi  )

Jadwal Training MACHINERY FAILURE ANALYSIS AND TROUBLESHOOTING

  • 05 – 07 Maret 2017
  • 26 – 28 April 2017
  • 16 – 18 Mei 2017
  • 15 – 17 Juni 2017
  • 13 – 15 Juli 2017
  • 24 – 26 Agustus 2017
  • 14 – 16 September 2017
  • 13 – 15 Oktober 2017
  • 16 – 18 November 2017
  • 15 – 17 Desember 2017

INVESTASI MACHINERY FAILURE ANALYSIS AND TROUBLESHOOTING

Rp. 6.000.000,- / peserta.. Sudah termasuk Makan Siang ,Coffee Break 2x,Modul Pelatihan dan Sertifikat.

MACHINERY FAILURE ANALYSIS AND TROUBLESHOOTING

 

 

Formulir Pra-Pendaftaran Public Training / Permintaan Informasi Lebih Lanjut
  1. JENIS INFORMASI/TRAINING
  2. (required)
  3. (required)
  4. DATA PRIBADI
  5. (required)
  6. (required)
  7. (required)
  8. (valid email required)
  9. (required)
  10. (required)
  11. DATA PRE REGISTRATION (Tidak Mengikat)
  12. (required)
  13. PESAN UNTUK PENYELENGGARA TRAINING
 

cforms contact form by delicious:days

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.